What Size Water Inlet Fitting For Bosch 800 Series Dishwasher
Installation Instructions
Important Safety Instructions
Delight READ and SAVE this information
To avoid possible injury or property damage, OBSERVE ALL WARNINGS AND CAUTIONS.
These instructions are intended for use by qualified installers only. The dishwasher must be installed by a qualified service technician or installer.
- In add-on to these instructions, the dishwasher shall exist installed to encounter all electrical and plumbing codes and ordinances (both national and local).
Read these installation instructions completely and follow them carefully. They volition salve you time and effort and assist to ensure safety and optimum dishwasher performance.
IMPORTANT
- The dishwasher bleed hose must exist installed with a portion of it at least 33″ (84 cm) off the cabinet floor; otherwise the dishwasher may not drain properly.
- This dishwasher is intended for indoor residential use but, and should not exist used in commercial food service establishments.
- NEW INSTALLATION – If the dishwasher is a new installation, almost of the piece of work must be washed earlier the dishwasher is moved into place.
- REPLACEMENT – If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts every bit necessary.
- This appliance has been found to be in compliance with Can/CSA-C22.2 No. 167/UL 749. Information technology is the responsibleness of the owner and the installer to determine if boosted requirements and standards apply in specific installations.
- Not for outdoor use.
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or corrective impairment. Report any damage immediately. Cosmetic defects must be reported within 30 days of installation.
NOTE: Do not discard any bags or items that come with the original package until afterward the entire installation has been completed.
Warning
Avoiding Full general Hazards
Practice not use the dishwasher until it is completely installed. When opening the door on an uninstalled dishwasher, carefully open the door while supporting the rear of the unit. Failure to follow this alert can crusade the dishwasher to tip over and result in serious injury.
Before installing the "L"-shaped supplied countertop mounting brackets (select models), decide which method will exist used to secure the dishwasher into its opening. Once these mounting brackets are installed on the dishwasher, removing them is hard and will damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas tin form in a hot h2o system that has not been used for weeks. Hydrogen gas is explosive.
Before filling a dishwasher from a system that has been off for weeks, run the water from a nearby faucet in a well ventilated expanse until there is no sound or evidence of gas.
Temperatures required for soldering and sweating will damage the dishwasher's base of operations and water inlet valve. If plumbing lines are to be soldered or sweated, go along the rut source at least 6″ (152.four mm) away from the dishwasher'due south base and water inlet valve.
Removing any cover or pulling the dishwasher from the chiffonier can expose hot water connections, electrical power and sharp edges or points. Handle with intendance.
Fugitive Electrical Shock/Fire Hazards
Practice not allow the electrical and water supply lines to touch. Separate channels are provided under the dishwasher.
Do not piece of work on an energized circuit. Doing and so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any piece of work on the dishwasher electrical supply circuit until y'all are certain the circuit is de-energized.
Make sure electrical work is properly installed. There should exist no loose electrical connections. Ensure all electric connections are properly made.
The client has the responsibility of ensuring that the dishwasher electric installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, sixty Hz, AC, continued to a dishwasher-dedicated, properly grounded electrical excursion with a fuse or breaker rated for 15 or twenty amps. Electrical supply conductors shall exist a minimum #xiv AWG copper only wire rated at 75°C (167°F) or college.
This appliance must be continued to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the excursion conductors and continued to the equipment-grounding terminal or atomic number 82 on the appliance. Practise non use extension cords.
Avoiding Plumbing/Scalding Hazards
Practice not perform any piece of work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not endeavor any work on the dishwasher hot water supply plumbing until yous are certain the hot water supply is close off.
Do non over tighten the xc° elbow. Doing and then may impairment the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating will damage the dishwasher's h2o inlet valve. If plumbing lines are to be soldered or sweated, keep the rut source at least 6″ (152.4 mm) away from the dishwasher's water inlet valve.
Check local plumbing codes for canonical plumbing procedures and accessories. All plumbing should exist done in accordance with national and local codes.
These instructions depict an installation method for stainless steel braided hose or PEX hot water supply lines. If using copper tubing or other material for h2o supply, defer to a licensed plumber for proper installation.
Suggestion 65 Alert:
This product may contain a chemical known to the State of California, which tin cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label equally required by California:
STATE OF CALIFORNIA Suggestion 65 Warning:
Warning
Cancer and Reprodutive Harm – world wide web.P65Warnings.ca.g4ov
Tools and Materials Needed
Hammer Pigsty Saw Pipe Wrench
Adjustable Wrench Tape Measure out Slot Screwdriver
Torx T-20 Screwdriver Wire Cutter Wire Stripper
Ø ii mm (1/xvi in) Drill Level
Materials Supplied
| A | Extra Tall Detail Sprinkler * |
| B | Toe Panel Screws |
| C | Mounting Brackets |
| D | Mounting Bracket Screws |
| E | Toe Panel (ii pieces) |
| F | Toe Panel caps and screws (select models simply) |
| G | Screw Clench (for hose) |
| H | H2o Supply Adaptor Fitting |
| I | Flexible Border Protector Grommet for electric wire |
| J | Rubber Drain Hose Adaptor |
| M | Toe Panel Mounting Brackets (select models only) |
| Fifty | Outer toe console (third slice) (select models only) |
| G | Side Mount Strength Distributor (Alternate Side Mount merely) |
| N | Mounting Bracket Screws (Alternate Side Mountain only) |
| O | Installation Guide for Fully Integrated Door Panel (select models only) |
| P | Power Cord |
| Q | Wrench (wrench size 13) |
* Depending on the model of your dishwasher. Also available from Customer Service.
Enclosure Requirements
| |
| Avoid Scalding or Electrical Daze Hazard! |
Notation: This dishwasher is designed to be enclosed on the top and both sides past standard residential kitchen cabinetry.
Select a location every bit close to the sink as possible for like shooting fish in a barrel access to h2o supply and drain lines.
For proper dishwasher operation and advent, ensure that the enclosure is foursquare and has the dimensions shown in Figure 1 below.
Effigy 1
Annotation: If your dishwasher opening width measures >18″ (458mm) apply the TOP mounting method.
If your dishwasher opening width measures 18″ (458mm) use the SIDE MOUNT mounting method.
If the dishwasher is to be installed in a corner, make sure that in that location is acceptable clearance to open the door. Come across Effigy 2 below.
Effigy two
| |
| Avert Electric Shock/Fire Adventure |
Later locating the proper place for your new dishwasher, you will need to create any required openings to allow for passage of the water, drain and electrical line. In society to avoid interference with the dishwasher when sliding it into the chiffonier, place your openings within the dimensions shown in Effigy 3 beneath.
Figure 3
Required Openings:
ane½″ (38 mm) diameter- To pass the included electric supply junction box through to adjacent cabinet. The edges of the opening should, if the sectionalisation is woods, exist shine and rounded or, if the partition is metallic, be covered with the grommet (I) provided for this purpose by the manufacturer.
Note: If the incoming electric supply, water supply and drain connections are all in the same cabinet, the 1 iv¾" x 23/8″ (120 x threescore mm) hole will exist large enough for all three to laissez passer through.
4″ x 2″ (100 x l mm) – To pass the included h2o supply line toward the water supply
1¼" (32 mm) diameter – To laissez passer the dishwasher bleed hose toward the drain connection
Before sliding the dishwasher into the chiffonier, remove the hose prune at the back of the dishwasher as shown in Figure 4. The hose clip may be used afterwards to hold the bleed hose as shown in Figure seven.
Figure 4
Electric Grooming
| |
| Avoid Electrical Shock Hazard! Do not work on an energized circuit. Doing so could result in serious injury or death. Just qualified electricians should perform electrical piece of work. Do non try whatsoever work on the dishwasher electric supply circuit until you are certain the excursion is de-energized.Improper connection of the equipment-grounding conductor tin result in a run a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.Exercise Not alter the plug provided with the appliance; if information technology will not fit the outlet, accept a proper outlet installed by a qualified electrician. To avoid possible injury or property damage, intendance should be exercised when the dishwasher is installed or removed to reduce the likelihood of damage to the power cord. Avoid Fire Hazard! Loose and improperly installed electrical connections can result in overheating! Wall Socket Connections: Only apply the provided power cord for wall socket connections. Permanent Wire Connections (in add-on to the warnings above): Only use the junction box power cord, sold as Accessory kit #SMZPCJB1UC. |
Electrical Supply
The customer has the responsibility of ensuring that the dishwasher electric installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, sixty Hz, Ac, connected to a dishwasher-defended, properly grounded electrical circuit with a fuse or billow rated for 15 or 20 amps.
Dishwasher Electric Rating
| Volts | Hertz | Amperes | Watts |
| 120 | lx | 12 | ane,440 (max) |
Grounding Instructions
This appliance must exist grounded. In the upshot of a malfunction or breakdown, grounding will reduce the hazard of electric shock by providing a path of least resistance for electric electric current. This appliance is equipped with a cord having an equipment-grounding usher and a grounding plug. The plug must exist plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
Make certain that the dishwasher is continued to a suitable ground in compliance with all local codes or, in the absence of a local code, with the NATIONAL ELECTRICAL Lawmaking in the United States or the CANADIAN Electric CODE C22.1-latest edition in Canada too equally whatsoever provincial/country or municipal or local codes that apply.
Note: Installations requiring difficult wiring and terminal cake – The accessory terminal cake/junction box model, SMZPCJB1UC, designed for permanent wire connectedness, is not included merely tin can be ordered through Customer Service by calling 1-800-944-2904. Follow the instructions included with the kit.
Figure 5
- Place adhesive backed cord clips (provided in the installation kit) as shown in the figures above and route power cord through the clips. Plug the cease of the supply cord into the back of the dishwasher.
- The outlet for the power supply cord should be located in a chiffonier or wall adjacent to the dishwasher cabinet. Practice non plug dishwasher in until all the steps of installation are complete.
Note: Merely use the included power cord. If cord is missing order kit SMZPC002UC through Customer Service.
Inlet Water Connections
Hot H2o Supply
The hot water heater should exist set to deliver approximately 120° F (49° C) h2o to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures volition increase run times. The hot water supply pressure must be betwixt 15 – 145 psi (1 – 10 bar).
Important NOTES:
- If using a solder joint instead of a pinch fitting, exist sure to make all solder connections earlier connecting the water supply line to the dishwasher.
- Make sure at that place are no sharp bends or kinks in the water line that might restrict water flow.
- Always utilize the appropriate seal when making plumbing connections.
- Before connecting the water supply line to the dishwasher, flush the incoming h2o line for approximately 5 minutes to clear any strange textile.
- Turn on the water supply and check for leaks subsequently connections are made.
| |
| Avert Scald Risk! |
| CAUTION |
| Temperatures required for soldering and sweating will impairment the dishwasher. If plumbing lines are to be soldered or sweated, keep the rut source at least 6 inches (152.4 mm) away from the dishwasher. |
H2o Supply Close Off Valve
Install an hands attainable shut-off valve (not supplied) in the hot water supply line, as shown in Figure 9. All solder connections must be made before the water line is connected to the dishwasher.
Connecting the Hot Water Supply
There are two plastic corrugated hoses that go out the dorsum of the dishwasher. The larger hose, with the brass fitting on the stop, is the water supply hose to the dishwasher (the other hose is the dishwasher drain hose). You will demand a iii″ x one¾" (76 10 45 mm) opening through the cabinet to pass the dishwasher h2o supply line through toward the shut off valve.
Effigy vii
To connect the hot water supply:
- Assemble the water supply adaptor plumbing fixtures (H) from the parts bag onto the dishwasher h2o supply hose. This connexion does not crave Teflon brand tape.
- Pass the dishwasher h2o supply line with attached adaptor through the opening toward the h2o close off valve. Take care not to allow the hose to kink or twist behind the dishwasher.
- Connect the dishwasher h2o supply line with adaptor to the water shut off valve. You volition demand to employ an approved dishwasher water supply line with the correct fittings for this connectedness. Always use the appropriate seal when making plumbing connections.
Notation: The end of the dishwasher water inlet hose is heavy and will need to be supported. It is best to lay the end on the cabinet floor equally shown in Figure vii. - After all connections are made, plow on the hot water and bank check for leaks.
Bleed Connections
The dishwasher drain hose may be connected to the household or field drain plumbing in one of 4 means. You will need a i¼" diameter hole in guild to laissez passer the drain hose through the cabinet.
- Straight nether the sink dishwasher drain connection, as shown in Figure 9.
- Directly to a disposer dishwasher bleed connectedness, equally shown in Effigy ten.
- To the under sink dishwasher bleed connexion through an air gap, every bit shown in Effigy 11.
- To a disposer dishwasher bleed connection through an air gap, as shown on Figure 12.
IMPORTANT NOTES:
- If local ordinance require an air gap, install it according to the manufacturer's instructions.
- If the dishwasher drain hose is to be connected to a disposer dishwasher drain connexion, remove the plug from the disposer's dishwasher drain connection.
- The dishwasher bleed hose must accept one place along its length that is securely attached 20″ (508 mm) above the cabinet floor.
- The drain hose length tin be extended if necessary. The maximum length of the drain hose, including the hose leading to the air gap, is 150″ (3800 mm).
Figure 8
Figure nine Figure x
Figure xi Figure 12
Installation of Rubber Drain Hose Adaptor
For a big port, employ the drain hose as information technology is.
- For a small port, insert the condom drain hose adaptor into the drain hose end.
- Obtain the Rubber Drain Hose Adaptor (J) jump clamp from the Dishwasher Installation Kit (do not substitute).
- Insert the dishwasher drain hose into the cease of the drain hose (encounter Effigy 13.) Be certain to fully insert the drain hose.
- Apply the clamp provided to adhere the Condom Drain Hose Adaptor to the house plumbing equally shown in Figure 14.
Figure 13
Figure 14
Installation of Mounting Brackets
| Circumspection |
| Before installing the supplied countertop mounting brackets, decide which method of securing the dishwasher into its enclosure will be used. Once the mounting brackets are installed on the dishwasher, removing them is difficult and will harm the mounting brackets and the dishwasher. |
The dishwasher tin can be secured into its enclosure in two means:
NOTE: If your dishwasher opening width measures >18″ (458 mm) use the TOP MOUNT mounting methods. If your dishwasher opening width measures eighteen″ (458 mm) use the SIDE Mount mounting method.
Superlative Mountain is used for countertops fabricated of wood or other materials that can be easily drilled, or for openings wider than 18″. Orient the mounting brackets as shown in Effigy 15 and position the two pocket-sized tabs on the mounting brackets over the two slots on the dishwasher's front corners. Push the mounting brackets down firmly to insert the tabs into the slots.
Side Mount is for countertops made of marble, granite, or other very difficult materials that cannot exist easily drilled. Also, it is for for openings that are 18″. Insert a side mount force distributor (Chiliad) in each side as shown in Figure sixteen.
Figure 15
Elevation Mount
Effigy 16
Side Mountain
| |
| Avoid Tip Over Take chances! |
LEVELING THE DISHWASHER
The unit should at present exist set to slide into the cabinet opening. To avoid scratching the flooring, utilize floor protection and caution when sliding the dishwasher into the cabinet. Make sure that the hoses and cords do not bunch upwards backside the unit or kink as y'all slide the unit dorsum. Make sure to slide the unit into identify before raising the leg levelers. Level the dishwasher horizontally by turning feet clockwise to raise or counter-clockwise to lower front of the unit. Level the dishwasher vertically by turning center screw to raise or lower the back.
Figure 17
SECURING THE DISHWASHER
Center the dishwasher in the opening before securing it to your cabinet or countertop equally shown in Figure xviii. Remove the superlative cutlery rack as shown in Figure 19 *.
Figure xviii
Figure nineteen *
Drive the mounting screws through the holes in the mounting brackets as shown for Pinnacle Mountain (Figure 20), Side Mount (Effigy 21).
Effigy 20
For Summit Mount
Figure 21
For Side Mount
* Depending on whether the dishwasher includes a height cutlery rack.
Attaching the Toe Panel
Your dishwasher comes with either a two-slice or three-piece toe panel (model dependent) to allow tiptop aligning.
- Position the slotted rear toe panel (function of East) on the dishwasher start. Allow it to balance on the floor.
- Position the mating front end toe panel (part of E) on pinnacle of the rear toe panel allowing the angled edge to rest on the mating edge of the dishwasher.
- Drive the two blackness screws (B) through the holes in the toe console to secure. Use the supplied screws to avoid damaging the dishwasher. See Figure 22
- For models with outer toe panel (tertiary piece – L) slide the brackets (Yard) provided, into the slots of the toe panel you just attached.
- Once you determine the correct position for the brackets, remove the bracket and bend the metal tab. See Figure 23. This ensures that the toe panel will not slide in further than y'all demand.
- Re-insert the brackets.
- Attach the outer toe panel (Fifty) onto the brackets and drive the screws provided (F) in place to secure the toe panel.
Figure 22
Effigy 23
Customer Service
Your dishwasher requires no special care other than that described in the Intendance and Maintenance section of the Utilise and Intendance Transmission. If yous are having a problem with your dishwasher, before calling for service please refer to the Self Help section in the Use and Care Transmission. If service is necessary, contact your dealer or installer or an authorized service center.
Do non attempt to repair the appliance yourself. Whatever work performed by unauthorized personnel may void the warranty. If you are having a trouble with your dishwasher and are not pleased with the service y'all take received, please take the following steps (in the order listed below) until the problem is corrected to your satisfaction:
- Contact your installer or the Authorized Service Contractor in your area.
- E-postal service us. Run across your Use and Care Manual for instructions.
- Write us at the address beneath:
BSH Domicile Appliances, Corp.
1901 Main Street, Suite 600
Irvine, CA 92614 - Phone call united states of america at the Customer Service phone number:
1-800-944-2904
Please be sure to include (if you are writing), or have available (if y'all are calling), the following data:
- Model number
- Serial number
- Date of original purchase
- Date the problem originated
- Caption of the problem
- Daytime phone number where you can exist reached.
Delight make a copy of your invoice and keep it with this manual. The client must bear witness proof of purchase to obtain warranty service.
Documents / Resources
References
-
P65Warnings.ca.gov
What Size Water Inlet Fitting For Bosch 800 Series Dishwasher,
Source: https://manuals.plus/bosch/800-series-ada-24-inch-custom-panel-dishwasher-manual
Posted by: mixonkinces69.blogspot.com
0 Response to "What Size Water Inlet Fitting For Bosch 800 Series Dishwasher"
Post a Comment